LOADING...

LINKSYS PAP2T CONFIGURATION PDF

Here’s the setup and configuration for a Linksys PAP2t for VoIP. Manual for basic configuration and management. Linksys is a registered trademark or trademark of Cisco. Systems, Inc. and/or its affiliates in the U.S. and . Linksys PAP2, PAP2-NA, PAP2T-NA BYOD VoIP SIP Setup and Configuration guide with Internet Phone Service Provider.

Author: Goltir Mijar
Country: Grenada
Language: English (Spanish)
Genre: Science
Published (Last): 14 May 2013
Pages: 491
PDF File Size: 19.75 Mb
ePub File Size: 17.1 Mb
ISBN: 925-8-19110-865-7
Downloads: 43663
Price: Free* [*Free Regsitration Required]
Uploader: Vugrel

Your router’s firewall also known as NAT is blocking certain operations of the VoIP telephone adapter or some of the settings of the adapter is not entered correctly. Using compression like G does is processor intensive and both these ATA models cojfiguration not have a capacity to handle simultaneous G calls.

Each phone port operates independently with separate phone service and their own phone numbers, line 1 and line 2. Go to any browser equipped computer on your network and enter the address: The following instructions are typical instructions for line 1.

So, if Line 1 is on G. If you are having issues dialling out, go to Regional tab and at the Vertical Service Activation Codes section remove all the feature codes. When one line port uses G.

I understand that I can withdraw linskys consent at anytime. To do this, you need to pick up the phone attached to the Line 1 jack and dial: Each phone jack operates independently, with separate phone service and phone numbers – like having two phone lines.

  GROUTING OF ROCK AND SOIL KUTZNER PDF

How to Set Up the Linksys PAP2T Telephone Adapter

These are optional settings, but are highly recommended to get the best experience out of your phone. Use the above as an example as your system administrator may be able to provide you with your company’s internal NTP servers. This is provided in your welcome email. Search Help My Account. Device will now get settings remotely from our servers.

See this page for further information. Enter your full name, this will show up as part confighration your caller ID. Unplug your device from the power and plug back after 5 seconds to reboot the device.

How to configure a Linksys PAP2t for VoIP.

Just plug it into your home Router or Gateway and use the two standard telephone jacks to connect your existing phones. Typically G, which is an un-compressed codec would be the choice, but to conserve on bandwidth you might change Line 1 “Preferred Codec” to Ga. Under Subscriber Information put your name into Display Name.

What is your data connection? Once the phone has rebooted and is back online, go to the Info tab and scroll down to Line 1 Status and check the Registration State shows Registered. Click on the “Admin Login” button near the top right side of the screen, then click on the “Line 1” tab. Set Locale to en- GB.

  GA-MA790XT-UD4P MANUAL PDF

How to Set Up the Linksys PAP2T Telephone Adapter [SureVoIP Support]

Less Than 1 Month. If you are experiencing issues with voice hearing the caller or the caller hearing you and so onthen ensure you have followed Step 5 above.

If registration is failing, check over the settings entered above. Please refer to our Privacy Policy or Contact Us for more details. If the phone fails to login, please take the time to double check your configuration as above. To save kinksys, you can change Line 1 “Preferred Codec” to Ga. Click on the “Admin Login” button near the top right side of the screen, then click on the “Line 1” tab.

If you get one-way audio, you are probably behind NAT. Make the following changes on LINE 1 you have to click on advanced view to see these options.

For more information on the Cisco range of IP phones, please visit the Cisco phones product website. Except where otherwise noted, content on this wiki is licensed under the following license: The Preferred codec drop down box has several choices.