Find great deals for Dolby Laboratories CP Digital Cinema Processor. Shop with confidence on eBay!. The Dolby CP series is designed for easy operation in today’s multiplex environment. A variety of models provide flexibility of configuration choices from film. Dolby CP Dolby Digital Cinema Sound Processor: : Industrial & Scientific.
|Country:||Turks & Caicos Islands|
|Published (Last):||21 November 2006|
|PDF File Size:||5.95 Mb|
|ePub File Size:||16.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
Dolby Laboratories CP650 Digital Cinema Processor
Transferring Settings Between Two Cps 7. To gain access to the CP circuit boards: Chapter 7 Final Adjustments 20 milliseconds after the arrival of sound from the front speakers.
Microphone balanced with phantom power. Projector Clean the optical surfaces with a cotton swab moistened with glass cleaner.
The Marketplace for Musicians |
If this dklby does not improve the response, dolb problem may be a degraded slit or lens damage. The pinout of this connector is determined by the type of option board installed in the connectors of the Cat. Page 98 Format 10 requires the Dolby Digital Cat. E-1 Control Via Remotes Connector Locate the power amplifiers away from the CP to avoid hum pickup problems.
Comments to this Manuals Your Name. If it becomes necessary to replace the LED, follow the procedure outlined below. Press the OK button to save the assignment to the Saving Changes Bsl and Bsr channelsand Rs. Figure shows the switch location.
Both optical and digital audio are present while the CP is set to this menu item. The delay is adjustable from 20 to ms in 1 ms steps. With a correctly aligned digital reader, most films will play at an error rate of 6 or lower. Control Via Remotes Connector While this was never intended to be a feature of the remote port, it may be possible to command the CP to change the fader level, select any one of the eight front-panel formats, and to toggle the mute status.
If neither is available, close inspection of the film itself will help distinguish the various types. Verify that all power connectors are fully inserted into their sockets. The motor start connector is used to interconnect the changeover control lines of the CP with the theatre control system. If you wish to use a connector already wired for use with a Dolby CP, add a jumper between pins 5 and 6.
DOLBY LABORATORIES CP INSTALLATION MANUAL Pdf Download.
Dolny 1—1 Formats Supported by the CP The A-Chain optical level is calibrated with the Cat. To print the manual completely, please, download it.
Page 91 Turn on power to the digital soundhead and the CP Wiring from the stereo solar dloby to the CP Page 40 3 dB per octave above 2 kHz. Do not connect wires from any Dolby remote unit to terminal 4, 5, or 6.
Options available for the CP include a remote fader Cat.
Please update your browser to use Reverb
When the desired response for this channel has been achieved, press the right-hand OK button to save the settings. Pins 1, 2, and 5 are wired in parallel with the rear panel microphone input XLR connector. Any changes to settings will occur immediately, but will not be saved until this button is pressed.
Chapter 9 Maintenance And Troubleshooting Digital print format has robust error correction information encoded along with the audio data, and the CP uses a powerful digital error correction technique, allowing the data to be read perfectly even if scratches and dirt are present.
Don’t have an account? Be aware that leaving the CP set to No Reversion mode prevents automatic switching to optical sound if there is a loss or failure of the Dolby Digital soundtrack. External setup software available in several languages facilitates calibration, trouble-shooting, software upgrades, and transferring settings via a personal computer.
Chapter 8 Accessories The combined length of connecting cable to all the remote units should not exceed m ft.
Use the white painted semi-circles for angular alignment of tension arms. The setting is stored to CP memory using the procedure outlined below.
The Cp6550 will operate perfectly without setting the clock. LED Brightness Confirmation and Adjustment The optimum peak video signal voltage unobstructed light through the do,by hole is 4 V, measured from the 0 V reference baseline to the upper trace.
Troubleshooting Chapter 9 Maintenance and Troubleshooting Enter text from picture: Redirect the light from the offending source or keep it off during a showing. There must be a connection between the ground pins at the Cat. PCM or Dolby Digital consumerand configures the decoder appropriately. Got it, continue to print. Press the OK button.